OMEGA -OTW SERIES H
OMEGA -OTW SERIES H
Performance Parameters :
| Application* | Measurement of Wheel Axle Loads of various vehicles with pneumatic Tyre |
| Scope of Supply* | 2 Nos of weigh pads of active weighing surface, Digital controller, PC Software, Ramps or mats and carry case for weigh pads and ramps |
| Portable Axle Weigh Pads should be easy to carry and should be of slim size* | Yes |
| Capacity per Portable weigh Pad in Tons* | 10 |
| Size of the platform in mm* | Standard Suitable for Heavy Commercial Vehicles (Size should be min 380 x 650 mm) |
| Height of platform in mm* | 25 |
| Weight of the platform in kg* | |
| Capacity Per Axle in Tons* | 10 |
| Readability in kg* | 5 |
| Out Put Sensitivity in mv/Volt* | 1.2 |
| Non linearity in % FS* | 0.3 |
| Accuracy Static Mode in % of FS* | 1 |
| Maximum excitation Voltage in volts* | 9-15v |
| Corner error (FS)* | 0.5 to 150% of FS |
| Safe Over load in tonnes of % FS* | 125 |
| Maximum Over load in tonnes % of FS* | 250 |
| Mode of connectivity from weighing pad to digital system* | Both cable and wifi |
| Minimum length of connecting cable from weigh pad to digital system* | NA for Wifi |
| Suitable Ramp to the size of weigh pads* | YES |
| Type of Display* | LCD |
| Display features* | High contrast for good reading, double LCD Display with back it |
| Memory storage (Readings)* | |
| Maximum Operating Relative humidity* | 90% |
| Operating temp range* | -10 to 50 |
| Built in clock and micro printer* | Yes |
| Facility to enter vehicle No* | Yes |
| Keypad* | Menbrane |
| Print out format* | in built recharge battery and power source for operating and charging batteries to be single phase 230 volt 50 hz |
| Accuracy Class for the system* | OIML NO 76 CLASS 4 |
| Certificate No and date for Accuracy class* | |
| Protection Class* | IP 65 |
| Certificate No for protection class* | |
| Serail port connection* | RS 232 |
| Dimensions of the weighing pad system which should be easily carriable* | |
| The configuration drawing with dimensions should be submitted if asked by the buyer before supplies after placement of order* | Yes |
| Weight of the total system in KG* | |
| Material Parameters | |
| Weighing Pad Material* | Stainless Steel |
| Material of Ramp* | Stainless Steel |
| Additional Parameters | |
| Leveling mat supplied* | Yes |
| Suitable Carrying case to be supplied* | Yes |
| Certifications | |
| Model Approval Certificate from Director of Legal Metrology* | Yes |
| Model Approval certificate number and Date* | |
| OIML (international Legal Metrology ) approval (If available)* | Yes |
| The certificate no and date and put NA if not available* | |
| Manufacturer ISO Certified* | Yes |
| ISO Certification Details such as Certification No ,Validity etc and incase of No ISO certification please | |
| Put NA* | |
| Reports | |
| Type Test Certificate including Environment conditions from Regional Reference and Standard Laboratory (RRSL)hint: (As per RRSL only one capacity under same model series of same accuracy class is sufficient for remaining capacity of the same series &same accuracy class)* | |
| Test Report No and Date* | |
| Name of the lab* | |
| Address of the Lab* | |
| Each portable weighing pad system shall be supplied with calibration certificate and stamping under weights and measures act* | Yes |
| Model approval certificate,Type test and calibration certificate to be furnished to buyer at the time of supplies* | Yes |